to CSV to Excel chart Skip How do you want to save the recorded profile? profile recording\n WARMUP PREHEAT STEP1 STEP2 REFLOW COOLDOWN Start the oven's profile first or enable Autostart RECORDING FINISHED Recording of the profile has been stopped. Oven's process is still active! Warning Center Left Right CH1 CH2 CH3 CH4 Refl reference Preh reference Temperature Reference SHORT NAME: EXTRA INFO: PREH TEMP: PREH TIME: STEP1 TEMP: STEP1 TIME: STEP1 POWER: STEP2 TEMP: STEP2 TIME: STEP2 POWER: REFL TEMP: REFL TIME: REFL POWER: COOL SP: COOL TIME: MULTI ZONE TIME MODE Time(s) CENTER(°C) LEFT(°C) RIGHT(°C) CH1(°C) CH2(°C) CH3(°C) CH4(°C) No device connected Communication failed! Open failed! Connect the ProtoFlow. Disconnect the ProtoMat from USB if connected. Time(min) Device disconnected Unregistered Registered Start... Start connected Loading device data Current database not saved. Profiles opened from file. Cannot read profiles during profile recording. Stop the recording first.. Cannot read profiles while the process is still active. Finish the current profile first. Profiles read. Cannot save profile during profile recording. Stop the recording first. Cannot save profile while the process is still active. Finish the current profile first. Type down the profile number to be written(0-29). Profile will be set as current. Value should be between 0 and 29. Writing aborted. Profile written. Cannot save profiles during profile recording. Stop the recording first. Cannot save profiles while the oven is still active. Finish the current profile first. Writing profile . Wait... Profiles written. Export Data as CSV Export data to Excel(create chart) Zoom-out Set zoom to fit chart CSV File Saved FSP File Saved Profiles saved to file. Comma(,) cannot be used. Space has been used instead. Upgrading firmware. Wait! Upgrading done. Please restart the oven and load Factory profile. Type down the channel name (max. 5 characters): Name should be max. 5 characters long 30-day trial period exceeded! Please register to receive the licence. Cannot upgrade firmware while the oven is still active. Finish the current profile first. Turn OFF the oven and confirm by clicking OK Put the oven into BOOT mode. (Turn ON the oven and press adequate arrow key within 1 sec. Oven confirms the boot mode with OK.) Please select: - DOWN for Main program upgrade - UP for Heating control upgrade Press the adequate button below to start the selected firmware. Upgrade takes up to 10 min. Main menu is shown when upgrade is successfully finished. Optimization runs one profile to get a device specific ramp rate, which is included in Profile assistant to precisely set the parameters. Turn ON the oven and confirm the optimization. FlowShow SE cannot be used during optimization. Check occasionally to confirm opening/closing the drawer after the WARMUP. Optimization in progress. Do not turn off the oven. Please wait... Inappropriate ramp-up rate ( ). Default ramp has been used instead. Contact LPKF support! Restoring backup ( ). Please wait... Optimization done. Ramp rate has been added to Profiling assistant. Upgrade failed --> Please restart the procedure! Upgrading firmware. % done. Please wait. Erase done. Profile recording Built-in sensors Current oven profile Preheat reference Step2 T= MultiZone Preheat Cooldown Reflow Step1 T= description Measurement Extra info Short name Autostart(REGISTER) Status Process time Stop Profile recorder Profile programming Admin Profiling assistant Active database: No database: TIME MODE Cool time Cool speed Step 2 power Step 2 time Step 2 temp Step 1 power Step 1 time Step 1 temp PCB SIZE LARGE MEDIUM SMALL Profile number Refl power Refl time Refl temp Preh time Preh temp Write one Write all Draw Open Read all Save Serial number Firmware and software updates White papers send SN Register to gain some benefits (up-to-date firmware upgrades, technical documents, newsletter, etc.): REGISTRATION KEY: Optimize Help Email Send Firmware Sum of REFLOW, STEP1 and STEP2 time shouldn't be longer than 600s. Settings could not be saved. Please, set the FlowShow SE to run as administrator and restart the program. Copy Page Setup Print... Show Point Values Cannot read profiles while the oven is still active. Finish the current profile first. Cannot save profiles while the oven is still active. Finish the current profile first. Cannot upgrade firmware while the oven is still active. Finish the current profile first. Cannot start optimization while the oven is still active. Finish the current profile first. Language